Techniques for fishing the trout worm at Corona Lake Pics, Vids, and some good sound! Ah yes, the trout worm. Sitting on Lake Mary with my dad, we pulled on fish after fish and even managed to wrangle a 6 pound Alpers into the boat as the sun dipped below the skyline.
Steering wheel puller Here we go: Disconnect both battery terminals with 10mm wrench or socket and locate the leads where they cannot possibly come in contact with the battery or ground.
This is to be sure there is no power to the truck. Now go mow the lawn or whatever to give the juice time to "drain" from the truck. With a small flat blade, remove the cover on either side of the steering wheel to expose the T Torx screw that holds the airbag in place.
Disconnect the black wire with the white connector and the black and orange leads going into the airbag. Get a thin flathead under the yellow tabs on the connectors and pry up on the tab, and then just pull the connector straight out. Set airbag aside where it won't be disturbed. Remove steering wheel nut with 19mm socket with 3inch extension.
Once it's removed, mark the steering wheel and spindle with a Sharpie to be sure you'll reallign it correctly when reinstalling. I marked at 12 and 3 o'clock on mine. Install your wheel puller.
Be sure your bolts are the correct size so you do not strip the threads in the wheel. Once wheel is removed remove the 2 philips head screws on either side and remove the plastic trim pieces.
I had to mess with them a bit, but they will come out.
Just be sure not to muscle too much so you don't break any of the tabs that hold them together. Remove 2 connectors on the bottom of the clockspring.
One is black and one is yellow. Remove clockspring by disconnecting 3 plastic tabs. One on the top, and 1 on either side. Here's the top view.
Note dog hair gets into your entire truck. Set clockspring aside for later dissection! It's already centered via the orange tab that keeps it from spinning. You'll snap this off later. In the picture you'll see I have black electrical tape keeping mine centered because I broke off the tab when messing with it when I took it out of the box.
Reinstall your plastic trim once CS is inplace. Pull your orange tab off freeing up the clockspring to spin, but keep it centered. Reinstall your steering wheel with wires feeding through the top. Line up wheel to the marks you made on the spindle.
Tighten 19 mm nut. Connect orange and black to the airbag, and don't forget the other black wire.
Once they are connected, put airbag back in place and tighten your Torx on either side of the steering wheel. Replace the covers for the Torx.
Reconnect your battery and start truck to be sure your airbag light is now off."Employee Surveillance" Please respond to the following:Employers often want to find out if their workers are productive and loyal. Determine at least one limit that you would place upon a private employer’s rights to monitor the productivity and communications of employees at work.
Support your schwenkreis.comate whether employers should have more or fewer rights to monitor employee use of. LEG Discussion Question.
Best Resources for Homework and Assignment Help. All tutorials are delivered immediately via e-mail. LEG Discussion Question. Best Resources for Homework and Assignment Help. LEG Discussion Questions Week 2 to 10 . Has had 2 exposures that caused near anaphylaxis (not as bad as the peanut)- one when he was 10 months old and one when he was 1 year old.
(until then he had consumed egg in the cooked form, baked in homemade cakes and in Gerber foods) He was RAST'ed . This is a complete Journal issue. FOR MORE CLASSES VISIT schwenkreis.com LEG Week 2 Discussion Question Week 2 DQ "The Duty of Loyalty and Whistleblowing" Please respond to the following: Analyze the duty of loyalty in whistleblower cases to determine to whom loyalty is .
“Short- and Long- Run Impact” Please respond to the following: Evaluate the overall effectiveness of the Sarbanes-Oxley Act to date, and determine who has benefitted most from the passage of the act.